|
[SMS] - Superb Mini Server Project Support Forum |
![](templates/iCGstation/images/banner.jpg) |
|
![Reply to topic](templates/iCGstation/images/lang_english/reply.gif) |
View previous topic :: View next topic |
Author |
Message |
Auda Junior Member
Joined: 16 Nov 2008 Posts: 4
|
Posted: Tue Jan 06, 2009 5:41 am Post subject: Docs UPS lm-sensors HylaFAX e2fsck |
|
|
I have installed SMS and It looks good, very good. There are a few things that I either don't understand, can't find or have plain got wrong.
After I printed out "Samba-3 by example" from a pdf file, I found it on the hard drive in HTML format, but I cant find it again, where is it, or was I dreaming ? If I use Webmin to search for documentation it lists a lot but can't display them. I get "Invalid package documentation path"
I have a UPS is it possible to make SMS shutdown on a power failure ? Could I install Network UPS Tools (NUT)
Webmin can show me the temperatures of my drives, is it possible to show the CPU temp as well ? Could I install Lm_sensors - Linux hardware monitoring and have it show in Webmin ?
Checking large hard drives takes quite a while, could this be done as part of the shutdown routine rather than startup ?
How do I stop HylaFax from always starting on bootup ?
Thanks
Auda |
|
Back to top |
|
gerasimos_h Site Admin
Joined: 09 Aug 2007 Posts: 1757 Location: Greece
|
Posted: Tue Jan 06, 2009 8:41 am Post subject: |
|
|
man pages and docs are ripped off from SMS.Live.CD to save space.
They are available in SMS.Native.CD only.
You could, what brand is your UPS?
I had used in the past apcupsd with my APC ups, works perfectly.
You can install lm-sensors but I don't know if there is an lm-sensors webmin module available. I'll check it though.
Checking disks at startup is important and required in a power failure sittuation. If you have a power failure, at first boot disks must be checked, if not, your system might break, so checking disks in shutdown is not the best thing to do.
Unless you are not experience power failures, it would take months, even year between checking disks, since system it's up and running 24/7.
For hylafax edit /etc/inittab and remove or comment dialup line for faxgetty, and do
chmod -x /etc/rc.d/rc.hylafax
gerasimos_h _________________ Superb! Mini Server Project Manager
http://sms.it-ccs.com |
|
Back to top |
|
Auda Junior Member
Joined: 16 Nov 2008 Posts: 4
|
Posted: Mon Jan 26, 2009 11:27 am Post subject: |
|
|
I have been looking at lm-sensors. Webmin does have a module that supports it. I have installed lm-sensors however it doesnt go.
Running sensors-detect ends up with:
Sorry, no chips were detected.
Either your sensors are not supported, or they are
connected to an I2C bus adapter that we do not support.
See doc/FAQ, doc/lm_sensors-FAQ.html, or
http://www2.lm-sensors.nu/~lm78/cvs/lm_sensors2/doc/lm_sensors-FAQ.html
(FAQ #4.24.3) for further information.
If you find out what chips are on your board, see
http://secure.netroedge.com/~lm78/newdrivers.html for driver status.
I did a bit of looking and found this:
Compaq EVO D510 hidden sensor
http://www.lm-sensors.org/ticket/2304
* status changed from assigned to closed.
* resolution set to fixed.
Patch went in kernel 2.6.27-rc1
So doesn't that mean that it should work ? I have the 2.6.27.7-smp kernel
With regard to running e2fsck on shut down. My server is used at home and so gets no use between when I go to bed an when someone gets up in the morning so it gets turned off and thus saves between 1/4 and 1/3 on power. I agree that its important to check the drives on boot up, but every 20 boots it does a full drive check which takes maybe 5 or 10 minutes. So I figured if it did that on shutdown it would never do so on boot up, unless we have a power cut.
The UPS is called a Thor I havent looked into what else its called yet.
Thanks
Auda |
|
Back to top |
|
gerasimos_h Site Admin
Joined: 09 Aug 2007 Posts: 1757 Location: Greece
|
Posted: Tue Jan 27, 2009 10:48 am Post subject: |
|
|
Regarding fsck on shutdown you can download and replace
/etc/rc.d/rc.S
/etc/rc.d/rc.6
with those in the tar file here
Also you can change the frequency of mount times with
tune2fs -c [number of mount times] [your disk]
gerasimos_h _________________ Superb! Mini Server Project Manager
http://sms.it-ccs.com |
|
Back to top |
|
gerasimos_h Site Admin
Joined: 09 Aug 2007 Posts: 1757 Location: Greece
|
Posted: Mon Feb 02, 2009 8:50 pm Post subject: |
|
|
I don't know your status about lm-sensors but I have found little time and test lm-sensors...
First you should run sensors-detect
Slackware package is missing the init startup script, download the source and copy prog/init/lm_sensors.init to /etc/rc.d/ or /etc/init.d and run it after sensors-detect.
You should add it to /etc/rc.d/rc.local also to run at startup.
That was it.
from lm-sensors documentation:
The initial output of `sensors' will not be perfect. You have to adjust
the configuration file (/etc/sensors3.conf) to match your motherboard.
This includes (re)labelling inputs, ignoring unused inputs, changing
voltage compute lines and setting limits. Write down all the sensor
information your BIOS displays as a hint to what you are supposed to
obtain in the end. Make sure you modify the right chip section.
gerasimos_h _________________ Superb! Mini Server Project Manager
http://sms.it-ccs.com |
|
Back to top |
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You can attach files in this forum You can download files in this forum
|
|
![](templates/iCGstation/images/top.gif) |
![](templates/iCGstation/images/bt_left.gif) |
SMS - Superb! Mini Server Project © 2016
Powered by phpBB © 2001, 2002 phpBB Group
iCGstation v1.0 Template By Ray © 2003, 2004 iOptional
|
![](templates/iCGstation/images/bt_right.gif) |
|
|